{"id":3782,"date":"2023-04-29T17:17:37","date_gmt":"2023-04-29T15:17:37","guid":{"rendered":"https:\/\/www.sigalou-domotique.fr\/?p=3782"},"modified":"2024-04-21T12:59:21","modified_gmt":"2024-04-21T10:59:21","slug":"migration-jeedom-vers-home-assistant-le-lien-des-esp-sous-esp-easy-vers-ha","status":"publish","type":"post","link":"https:\/\/www.sigalou-domotique.fr\/en\/migration-jeedom-vers-home-assistant-le-lien-des-esp-sous-esp-easy-vers-ha","title":{"rendered":"Jeedom migration to Home Assistant, ESP link under ESP-Easy to HA"},"content":{"rendered":"

State of play on Jeedom<\/h3>\n

For now, my ESP (mostly Sonoff) is under ESP-Easy with the link to Jeedom via the plugin:<\/p>\n

\"espeasy<\/p>\n

Integration in Home Assistant<\/h3>\n

At this point, I don't want to reflash ESPs (with ESPHome for example) because I would like ESPs to be able to dialogue with Jeedom. and<\/strong> with HA.<\/p>\n

Adding a new controller in ESP-Easy<\/h3>\n

I helped myself with Dapolux's tutorial on https:\/\/forum.hacf.fr\/t\/integration-desp-sous-espeasy-via-mqtt\/2326<\/a>.<\/p>\n

To add a controller, go to the \u2018controllers\u2019 tab and add a second \u2018Home Assistant MQTT\u2019 controller.<\/p>\n

\"\"<\/p>\n

192.168.1.21 corresponds to the MQTT broker, on my config it is on the same machine as Zigbee2MQTT but depending on the configuration you can decide to have the MQTT broker elsewhere.<\/p>\n

Note: I used to put the end of the IP address in Unit Number to make sure I didn\u2019t have two identical Unit Numbers on my installation.<\/p>\n

\"\"<\/p>\n

On each device on the \u2018Devices\u2019 tab, tick \u2018Send to Controller 2\u2019 so that the information is sent to controller 2 (i.e. MQTT to HA)<\/p>\n

\"\"<\/p>\n

In the \u2018Tools\u2019 tab and then \u2018Advanced Settings\u2019, tick these boxes:<\/p>\n

\"\"<\/p>\n

Checking MQTT Frames on MQTT Explorer (Invoicing)<\/h3>\n

I like to check step by step that everything works.<\/p>\n

I launch MQTT Explorer, I connect to my broker in 192.168.1.21, I check that the frames of my equipment \"Pump Watering\" (in my example) appear well.<\/p>\n

\"\"<\/p>\n

So I know that my ESP sends the information well.<\/p>\n

Configuration on the Home Assistant side<\/h3>\n

Automatic discovery Not foreseen from ESP Easy<\/a>, we're going to have to configure manually<\/a> MQTT equipment in HA.<\/p>\n

I chose this ESP as an example for this tutorial because I have 3 different pieces of equipment to recover: a switch, a binary _sensor, a sensor<\/p>\n

The Juice Switch<\/h4>\n

The ESP GPIO12 corresponds to the control of the relay that powers or does not power the pump.<\/p>\n

\"\"<\/p>\n

I have often used the same word in name<\/strong> and in value<\/strong> (\u201cJuice\u201d in the example) to avoid confusion, be careful if you do not do this. The order to be followed in the HA configuration is [UNIT]\/[NAME]\/[VALUE]<\/p>\n

    \n
  • In the file \/config\/configuration.yaml<\/strong><\/li>\n<\/ul>\n

    Check that there is this line:<\/p>\n

    \n

    mqtt: !include mqtt.yaml<\/p>\n<\/blockquote>\n

      \n
    • In the file \/config\/mqtt.yaml<\/strong><\/li>\n<\/ul>\n
      \n

      switch:
      \u00a0\u2013 Name: Juice Pump Watering
      \u00a0 \u00a0single _id: switch.jus_pump_watering
      \u00a0 \u00a0command_topic: Pump Watering\/gpio\/12
      \u00a0 \u00a0state_topic: Watering\/Jus\/Jus Pump
      \u00a0 \u00a0payload_on: \"1\"
      \u00a0 \u00a0payload_off: \u20180\u2019
      \u00a0 \u00a0retains: true
      \u00a0 \u00a0device_class: outlet
      \u00a0 \u00a0device:
      \u00a0 \u00a0 \u00a0name: Watering Pump
      \u00a0 \u00a0 \u00a0Identifiers: \"Pump watering\"<\/p>\n<\/blockquote>\n

      \"\"<\/p>\n

      The binary _sensor \" Floater\"<\/h4>\n

      The ESP GPIO5 is an analogue input that corresponds to the position of my float in my water reserve. I switch off the pump if the float switches to 0.<\/p>\n

      [Note that \u201cGPIO5\u201d is the name and value in my example, I could very well have put \u201cFloater\u201d too]<\/p>\n

      \"\"<\/p>\n

      \n

      binary_sensor:<\/p>\n

      \u2013 Name: Float Pump Watering
      \u00a0 \u00a0single _id: binary_sensor.floater_pump_watering
      \u00a0 \u00a0state_topic: Water Pump\/GPIO5\/GPIO5
      \u00a0 \u00a0payload_on: \"1\"
      \u00a0 \u00a0payload_off: \u20180\u2019
      \u00a0 \u00a0device_class: moisture
      \u00a0 \u00a0device:
      \u00a0 \u00a0 \u00a0name: Watering Pump
      \u00a0 \u00a0 \u00a0Identifiers: \"Pump watering\"<\/p>\n<\/blockquote>\n

      \"\"<\/p>\n

      The \"Consumption\" Sensor<\/h4>\n

      The ESP I use is equipped with a CSE7766 chip that allows me to retrieve the pump consumption information.<\/p>\n

      What interests me is the W consumption of the pump, I will recover \u2018Power\u2019<\/p>\n

      \"\"<\/p>\n

      \n

      sensor:
      \u00a0 \u2013 Name: Consumption Pump Watering
      \u00a0 \u00a0 \u00a0single _id: sensor.consumption_pump_watering
      \u00a0 \u00a0 \u00a0state_topic: Watering\/Consumption\/Power Pump
      \u00a0 \u00a0 \u00a0_of _measurement unit: W
      \u00a0 \u00a0 \u00a0device_class: power
      \u00a0 \u00a0 \u00a0device:
      \u00a0 \u00a0 \u00a0 \u00a0 name: Watering Pump
      \u00a0 \u00a0 \u00a0 \u00a0 Identifiers: \"Pump watering\"<\/p>\n<\/blockquote>\n

      \"\"<\/p>\n

      Result in Home Assistant<\/h3>\n

      \"\"<\/p>\n

      \u00a0<\/p>","protected":false},"excerpt":{"rendered":"

      State of play on Jeedom For the moment, my ESP (mostly Sonoff) is under ESP-Easy with the link to Jeedom via the plugin:<\/p>","protected":false},"author":1,"featured_media":51,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[14,53,23],"tags":[61],"class_list":["post-3782","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-domotique","category-home-assistant","category-jeedom-2","tag-esp"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/posts\/3782","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/comments?post=3782"}],"version-history":[{"count":0,"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/posts\/3782\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/media\/51"}],"wp:attachment":[{"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/media?parent=3782"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/categories?post=3782"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.sigalou-domotique.fr\/en\/wp-json\/wp\/v2\/tags?post=3782"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}