![\"20200223](\"http:\/\/jeedom.sigalou-domotique.fr\/wp-content\/uploads\/2020\/02\/20200223_182855.jpg\")
<\/h2>\n<\/h2>\nNote: one V2 of this tutorial<\/a> was made with a Sonoff Basic R3<\/em><\/p>\n At a lower cost (within \u20ac10) + the price of heating (\u20ac16), I wanted to domotiser the heating of the bathroom to:<\/p>\n <\/p>\n Flashing the Sonoff, for that, there are hundreds of tutorials, I'm not going to do one more for that. The only detail to report is that the ESP_Easy_mega-20200222_normal_ESP8285_1M.bin file must be used during Flashing because the Sonoff module used is equipped with an ESP8285.<\/p>\n To help you, you can look this Tuto<\/a> or this Tuto<\/a> or this Tuto<\/a> that I did for other less documented modules<\/p>\n Connect the Sonoff to the local network and then integrate it into Jeedom<\/a><\/p>\n To do this, disable the serial port in the ESPEasy config, this allows you to recover the Rx and Tx terminals<\/p>\n For this step, you can set your temperature values (25\u00b0c in example) or timer (1h=3600s in example)<\/p>\n the Probe#Temperature do<\/samp> on button#button do<\/samp> we juice#jus do<\/samp> on System#Boot do<\/samp> On Rules#Timer=1 do <\/samp> In Jeedom, in the ESPEasy plugin, you can retrieve the temperature information, the status of your relay and add an on\/off command to control the relay.<\/p>\n Use this discussion<\/a> for any request for precision, support or assistance:<\/p>\nObjectives:<\/h2>\n
\n
Necessary equipment:<\/h2>\n
\n
![\"Screenshot](\"http:\/\/jeedom.sigalou-domotique.fr\/wp-content\/uploads\/2020\/02\/Screenshot_2020-02-23_D%C3%A9tails_des_commandes.png\")
<\/a><\/p>\n\n
<\/h1>\n
Implementation<\/h1>\n
<\/h2>\n
Step 1: Flashing<\/h2>\n
<\/h2>\n
Step 2: Connecting the Sonoff to Wi-Fi<\/h2>\n
<\/h2>\n
Step 3: Weld the temperature probe<\/h2>\n
\n
![\"connectsonoffbasicr2\"](\"http:\/\/jeedom.sigalou-domotique.fr\/wp-content\/uploads\/2020\/02\/connectsonoffbasicr2.png\")
<\/p>\n<\/h2>\n
Step 4: Disable Serial Port<\/h2>\n
![\"Screenshot](\"http:\/\/jeedom.sigalou-domotique.fr\/wp-content\/uploads\/2020\/02\/Screenshot_2020-02-23_Espeasy_-_Jeedom.png\")
<\/h2>\n<\/h2>\n
Step 5: Configure ESPEasy devices<\/h2>\n
![\"Screenshot](\"http:\/\/jeedom.sigalou-domotique.fr\/wp-content\/uploads\/2020\/02\/Screenshot_2020-02-23_SonoffSalleBain.png\")
<\/p>\nStep 6: Configure rules<\/h2>\n
\n if [Sonde#Temperature]>25 do<\/samp>
\n if [juice#juice]=1<\/samp>
\n gpio,13.1<\/samp>
\n gpio,12,0<\/samp>
\n timerSet,1,0<\/samp>
\n endif<\/samp>
\n endif<\/samp>
\nendon<\/samp><\/p>\n
\n if [button#button]=1<\/samp>
\n gpio,12.1<\/samp>
\n timerSet,1,3600<\/samp>
\n else<\/samp>
\n gpio,12,0<\/samp>
\n timerSet,1,0<\/samp>
\n endif<\/samp>
\nendon<\/samp><\/p>\n
\n if [juice#juice]=1<\/samp>
\n gpio,13,0<\/samp>
\n timerSet,1,3600<\/samp>
\n else<\/samp>
\n gpio,13.1<\/samp>
\n timerSet,1,0<\/samp>
\n endif<\/samp>
\nendon<\/samp><\/p>\n
\n gpio,12,0<\/samp>
\n gpio,13.1<\/samp>
\nendon<\/samp><\/p>\n
\n gpio,13.1<\/samp>
\n gpio,12,0<\/samp>
\nendon<\/samp><\/p>\nStep 7: Configure Jeedom<\/h2>\n
![\"Screenshot](\"http:\/\/jeedom.sigalou-domotique.fr\/wp-content\/uploads\/2020\/02\/Screenshot_2020-02-23_Espeasy_-_Jeedom1.png\")
<\/p>\nOperation completed<\/h2>\n